• Skip to primary navigation
  • Skip to main content
Extreme Coatings

Call: 888-367-2569

Plastics Industry Association Member

Engineered Surfaces to Extend Service Life and Performance

  • Home
  • About Us
    • Shows and Events
    • News
    • Houston Facility
  • Our Processes
    • High Velocity Thermal Spray
    • The Process
    • Encapsulation Protection
      • Full Encapsulation of Feedscrews
      • Partial Encapsulation of Feedscrews
    • Chrome Plating Replacement
      • Feedscrews, Mixing Rotors, etc.
      • Mud Rotors and Downhole Tools
  • Applications
    • Plastic & Rubber Industries
      • Feedscrews
      • Parallel Twin Feedscrews
      • Co-Rotating Twin Feedscrews
      • Ultrasonic Welding Horns
      • Cushion Master
      • Continuous Mixing Rotors
      • Mixer Bodies
      • Extrusion Dies, Die Plates, Sheet Dies
      • Granulator Knife Blades
      • High intensity Mixing Blades
      • Elbows For Pneumatic Conveying
      • Spin Dryer System
    • Oil & Gas Industry
      • Downhole Mud Rotors
      • Mandrels
    • Motorsports Industry
    • Marine Anti-Fouling
  • Technical Resources
    • Coating Formulas
      • Tungsten/Chromium Carbide
      • NiBoride
      • Other
    • Test Results
      • Abrasive Wear Test ASTM G65
      • Adhesive Wear Test ASTM G77
    • Case Studies
    • FAQs
    • Company Literature
    • ROI
    • Videos
  • How to Buy
    • Our Distributors
    • Purchase Encouragement Program (PEP)
    • Warranty
  • Contact Us
    • Application Profile Form
  • HVOF Thermal Spray
    Extreme Layer of Protection
    High Performance Formulas
  • Oil and Gas Industry
    Reduce Replacement Costs for Mud Rotors
    HVOF CPR delivers more abrasion and corrosion resistance than hard chrome plating (HCP) - even in high chloride environments
    Read More
  • Read More
    Twin Feedscrews
    Our high percentage carbide layer can provide from two to four times more wear life depending on fill loading.
    Plastic Injection Molding
  • Single Feedscrews
    Read More
    Feedscrews
    Our coatings are perfect for injection molders and extruders when processing fiberglass, calcium carbonate, titanium dioxide and metals, ceramic or other highly abrasive fillers.
  • Mixer-Extruders
    Continuous Mixing Rotors
    Our C1000 tungsten carbide has been used as chrome replacement in aggressive applications. C1000 doubles the working life of rotors compared to hard chrome plating.
    Read More
You are here: Home / Applications / Oil & Gas Industry / Mandrels

Mandrels

The Problem

As drilling environments become more aggressive, standard carbide coated mandrels have shown signs of performance inefficiency with cracking and coating delamination resulting in a short service life.

Solution

Extreme Coatings’ CarbideX Coated Mandrels

CarbideX® C9000Cr is a high tungsten carbide containing coating. This formula is designed to resist

  • Severe abrasion
  • Corrosion
  • Adhesive wear
  • Erosion
  • High temperatures up to 800° F

The deposits contain high levels of tungsten carbide in a cobalt-chrome-matrix designed for toughness and superior wear resistance.

Our CarbideX coating process differs from others on the market due to our attention to detail in coating preparation and finishing.

Results

Increased Service Life and Improved Performance Output

  • Lower cost per hour
  • Reduce motor failure rate
  • Longer run potential
  • Higher component utilization rate
PDF – Mandrels Carbide X

Refurbished mandrel with our CarbideX C9000Cr – a dense, crack-free coating designed to restore carbide coated or chrome-plated mandrels

Standard coated spline mandrel. Typical Issue: failure due to chloride attack, causing cracking and chipping

Standard bearing mandrel. Typical Issue: wearing at lower seal

Click here to increase the life of your mud rotors
Click here to increase the life of your extrusion & feed screws
Extreme Coatings

2895 46th Ave N - St. Petersburg, FL 33714

ISO 9001 2015 Certified by WCS ISO 9001:2015 Certified by WCS

888-367-2569

© 2015-2025, All rights reserved
Site by: Industrial Webworks, LLC

MENU
  • Home
  • About Us
    • Shows and Events
    • News
    • Houston Facility
  • Our Processes
    • High Velocity Thermal Spray
    • The Process
    • Encapsulation Protection
      • Full Encapsulation of Feedscrews
      • Partial Encapsulation of Feedscrews
    • Chrome Plating Replacement
      • Feedscrews, Mixing Rotors, etc.
      • Mud Rotors and Downhole Tools
  • Applications
    • Plastic & Rubber Industries
      • Feedscrews
      • Parallel Twin Feedscrews
      • Co-Rotating Twin Feedscrews
      • Ultrasonic Welding Horns
      • Cushion Master
      • Continuous Mixing Rotors
      • Mixer Bodies
      • Extrusion Dies, Die Plates, Sheet Dies
      • Granulator Knife Blades
      • High intensity Mixing Blades
      • Elbows For Pneumatic Conveying
      • Spin Dryer System
    • Oil & Gas Industry
      • Downhole Mud Rotors
      • Mandrels
    • Motorsports Industry
    • Marine Anti-Fouling
  • Technical Resources
    • Coating Formulas
      • Tungsten/Chromium Carbide
      • NiBoride
      • Other
    • Test Results
      • Abrasive Wear Test ASTM G65
      • Adhesive Wear Test ASTM G77
    • Case Studies
    • FAQs
    • Company Literature
    • ROI
    • Videos
  • How to Buy
    • Our Distributors
    • Purchase Encouragement Program (PEP)
    • Warranty
  • Contact Us
    • Application Profile Form
BraXe Rotors Inquiry
Sending